IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING - Risk of fire. Do not install insu-
lation within 3 inches of fixture sides or
wiring compartment, nor above the fixture
in such a manner as to entrap heat.
1. Electric current can cause painful shock
or serious injury unless handled properly.
For your safety, always remember the fol-
lowing:
· Turn off the power supply.
· Ground the fixture to avoid potential
electrical shocks.
· Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp sur-
face, or in water.
· Double check all electrical connections
to be sure they are tight and correct.
2. Specific safety information concern-
ing lamps:
· Match wattage of fixture and lamp ex-
actly.
· Do not remove or insert lamp when power
is on.
· Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
· Protect operating lamp from sources
of moisture.
Figure 1
Figure 4
Figure 2
Figure 3
Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier. Com-
pare the catalog description listed on the
packing slip with the label on the carton to
ensure you have received the correct mer-
chandise.
INSTALLATION INSTRUCTIONS
"APR"
Reflector
Part No. CJ520347
8/04
New Installation for APR Reflector
1. The GRS mounting frame utilizes an ad-
justable, flatspring, yoke assembly to re-
tain the reflector into the ceiling as
shown in Figure 2. The yoke assembly
must be properly installed onto the
mounting frame. Refer to the INSTAL-
LATION INSTRUCTIONS included in the
mounting frame for proper yoke instal-
lation.
2. The yoke assembly is preset at the fac-
tory for a ceiling thickness up to 1-5/8".
For other ceiling thickness, adjust the
yoke assembly by loosening the screws
on the yoke and moving the yoke down-
ward equal to the difference of the ceil-
ing thickness minus 1-5/8" (ex. 3" ceiling
thickness minus 1-5/8" = 1-3/8"). Refer to
scale on the yoke assembly for ease of
adjustment.
3. The socket cup is factory installed to
the flat spring. Pull socket cup down
into the ceiling opening until the flat
spring is fully extended as shown in Fig-
ures 2 and 3.
4. Attach socket cup to top of reflector by
aligning and engaging spring in socket
cup with slots in top of reflector as
shown in Figure 1. Lamp type markings
are located near the slots in top of re-
flector for proper positioning of socket
cup for optimum light distribution. If QRS
is included, install socket cup and neck
so that lamp bracket aligns with reflec-
tor slot as shown in Figure 5.
5. Install appropriate lamp as determined
by position of the socket cup/lamp type
marking on the reflector. For APR4 PAR30
and APR6 PAR38, remove reflector trim
from trim neck by twisting reflector
clockwise. Install lamp. Reverse proce-
dure for re-assembly of reflector. Be-
cause reflector must be removed for re-
lamping, a re-lamping pole cannot be
used. WARNING: Do not exceed the
wattage restrictions. If socket cup
adjustment is required: reach inside of
reflector, compress springs in socket cup
and move to appropriate reflector slot.
6. Push reflector through the ceiling open-
ing until the flat spring pulls it up to the
ceiling as shown in Figure 4.
7. If reflector does not rest tightly against
the ceiling, remove the reflector (See
step 8), adjust the yoke assembly up-
ward and re-attach reflector.
8. To remove the reflector: pull reflector
downward until the flat spring is fully
extended, remove lamp, reach inside of
reflector, compress springs in socket cup
and remove socket cup from reflector.
Socket
cup
Ceiling
Flat
Spring
Up
Flat
Spring
Down
Reflector
Figure 5
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals