IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING - Risk of fire. Do not install insu-
lation within 3 inches of fixture sides or wir-
ing compartment, nor above the fixture in
such a manner as to entrap heat.
1. Electric current can cause painful shock
or serious injury unless handled properly.
For your safety, always remember the
following:
• Turn off the power supply.
• Ground the fixture to avoid potential
electrical shocks.
• Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp sur-
face, or in water.
• Double check all electrical connections
to be sure they are tight and correct.
2. Specific safety information concern-
ing lamps:
• Match wattage of fixture and lamp ex-
actly.
• Do not remove or insert lamp when power
is on.
• Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
• Protect operating lamp from sources
of moisture.
Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier. Compare
the catalog description listed on the packing
slip with the label on the carton to ensure you
have received the correct merchandise.
INSTALLATION INSTRUCTIONS
Directional Lensed
Wallwash Housing
ROUGH-IN SECTION
for
DLWH 6 & 8
Part No. CJ520667
7/06
Page 1 of 2
WOOD OR STEEL JOIST CONSTRUCTION On 24”
centers (16” or 24” O.C. for 4” fixture) utilizing
solid type (non-accessible) ceiling (drywall,
plaster, etc.).
USING ROUTER FOR CEILING CUTOUT
1. Open lever (C) securing bar hangers - bend
ends of hangers 90° (D) to be used as nailing
tabs, center in the vertical slot, and close le-
ver (C) to lock; repeat on opposite side.
Refer
to Figure 1.
2. Secure a piece of plywood (E) to temporarily
span the bottom of the joists to support the fix-
ture housing while attaching the bar hangers
(F) to the joists. This will position the housing
correctly for drywall installer to provide pilot
hole (G) to locate fixture after ceiling has been
installed.
Refer to Figure 2.
3. PROCEED TO “FEED WIRE CONNECTION TO
FIXTURE J-BOX” ON NEXT PAGE.
Return and
complete following steps after feed wire con-
nections have been made.
4. Using 1/8” router follow outside of plaster
frame to cut hole in ceiling.
5. Loosen (2) 5/16” screws (A) 180° apart, al-
lowing fixture to drop down so bottom edge of
plaster flange will be slightly above edge of
ceiling material.
T-BAR CEILING INSTALLATION
1. Install ceiling panel in t-bar with ceiling
opening precut. Ceiling opening must be
slightly larger than the outside diameter of the
plaster flange.
2.Open lever (A), expand bar hangers (B) to
approximately 24” and close lever to lock. Re-
fer to Figure 3.
3. Through an adjacent opening, position the
mounting frame with the plaster flange pass-
ing through the precut opening with the
notches on the bar hangers engaging the t-
bar.
4. Secure the bar hangers to the t-bar by wire
or wiretie (by others) or bending end of bar
hanger. Refer to Figure 4.
5. Open lever and adjust mounting frame ver-
tically so that the bottom edge of the plaster
flange is flush or slightly above the bottom
edge of the ceiling panel.
6. PROCEED TO “FEED WIRE CONNECTION TO
FIXTURE J-BOX” ON NEXT PAGE.
7.
If fine tune adjustment from below ceiling is
required:
Loosen (2) 5/16” screws (A) 180°
apart, allowing fixture to drop fown so bottom
edge of plaster flange will be slightly above
edge of ceiling material.
PRIOR TO INSTALLATION
Read and familiarize yourself with the no-
menclature and instructions before starting
installation.
Turn off electricity at the breaker panel or
fuse box and follow National Electrical Code
regulations.
Figure 1
Figure 2
A
B
C
D
F
E
G
SAVE THESE INSTRUCTIONS
A
B
Figure 3
Figure 4
A
(2 pages)
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals