WARNING: Risk of fire. Do not install insulation
within 3 inches of fixture sides or wiring compartment,
nor above the fixture in such a manner as to entrap
heat.
This product must be installed by a person familiar
with the construction and operation of the product
and the hazards involved, in accordance with the
applicable installation code.
CJ5200903 Rev. B
6/10 1 of 2
©2009, 2010 Acuity Brands Lighting, Inc.
All Rights Reserved.
1. Electric current can cause painful shock or
serious injury unless handled properly. For you
safety, always remember the following:
•Turn off the supply power.
•Ground the fixture to avoid potential electrical
shocks.
•Do not handle an energized fixture or energize
any fixture with wet hands, when standing on a
wet or damp surface, or in water.
2. Specific safety information concerning
lamps:
•Match wattage of fixture and lamp exactly.
•Do not remove or insert lamp when power is
on.
•Do not scratch glass or subject lamp to undue
pressure as either may cause lamp breakage.
•Protect operating lamp from sources of
moisture.
• If lamp is marked it contains mercury.
Follow disposal laws. See:
www.lamprecycle.org
.
SAVE THESE INSTRUCTIONS
Upon receipt, thoroughly inspect for any freight
damage which should be brought to the attention of
the delivery carrier. Compare the catalog description
listed on the packing slip with the label on the carton
to ensure you have received the correct
merchandise.
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
NEW INSTALLATION FOR SQ SERIES
IMPORTANT! For wallwash housing
orientation installation details see
page 2.
Lay-in panel T-bar ceiling:
1. Cut ceiling opening slightly larger than the
outside opening of the mounting frame.
2. Position mounting frame through opening in
ceiling. Release clamping latch arms and
adjust channel bars to the correct spacing
between T-bar (see Figure 1). Secure channel
bars to T-bar by means of wire ties, screws or
by bending ends onto T-bar (see Figure 2).
3. Once mounting frame has been secured in
structure, adjust the mounting frame vertically
to align the bottom edge to either flush or
slightly above (1/8" max) the ceiling line (see
Figure 3). Secure mounting frame into position
by closing the clamping latch arm. The notch
located in the draw-down flange of the housing
can be used to assist with alignment of
multiple fixtures (see Figure 4).
4. If additional security is required, a No. 8
sheet metal screw, wire tie or wire (not
supplied) may be used to tie the latch arm to
the mounting frame (see Figure 1).
5. Remove knockouts on junction box to feed
power supply to fixture (see Figure 5). Supply
wire must meet applicable electrical codes and
be rated for a minimum of 90°C. Junction box
is thru-wire rated for 8-No. 12 AWG
conductors (4 in-4 out).
6. Complete necessary wire connections.
Snap the door onto the junction box.
7. To adjust housing alignment after
installation, see “Post Installation
Adjustment.”
CAUTION! For T4/T6 and low voltage
MR16 downlights, lens must be in place in
front of lamp before fixture is energized.
INSTALLATION INSTRUCTIONS
SQP, SQDLW, SQPH,
SQDLWH, SQTH, SQDLWTH,
SQDLV, SQDMRH Mounting Frame
Clamping
latch arms
Closed
Open
Figure 1
Figure 2
Figure 3
Figure 4
Bent tab
T-Bar
Channel
bar
Wire tie
Mounting
frame
Ceiling
Flush or
slightly
above
ceiling line
Sight
Notches
Figure 5
Remove
knockouts
as needed
!
(4 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals